FLTM_BI103標準鹽霧試驗箱

FLTM_BI103標準鹽霧試驗箱乃針對各種材質表面處理，包含涂料、電鍍、有機及無機及膜，陽極處理，防銹油，化成處理之耐蝕品質，進而達成製品長時間之耐蝕性。

產品規格
規格型號          實驗空間（W*D*H）      外箱尺寸（W*D*H）
SH-60             600*450*400mm          1075*630*1100mm
SH-90             900*600*500mm          1415*885*1285mm
SH-120           1200*1000*500mm         1900*1200*1400mm
SH-160           1600*1000*500mm         2300*1200*1400mm
SH-200           2000*1000*500mm         2700*1200*1400mm

可根據客戶特別要求，訂制非標產品。

三 zui大耗電量：AC 220V 單相3KW 50/60HZ

四 試驗溫度：
依CNS JIS ASTM GB2423.19規格，可設定式恒溫控制
A  鹽水噴霧試驗：NSS，ACSS
1、試驗室：35℃ ± 1℃
2、飽和空氣桶：47℃±1℃
B  耐腐蝕試驗：CASS（醋酸銅）
1、試驗室：50℃ ± 1℃
2、飽和空氣桶：63℃ ± 1℃

五 機體結構：
材質：
a、試驗室採用P.V.C聚氯乙稀板，耐高溫
b、試驗室密封蓋採用PVC耐沖擊板
c、試藥補充瓶採用隱藏式附水位表，清洗容易，不易破裂（氣壓缸自動開閉）
d、飽和空氣桶採用SUS#304不銹鋼耐高壓桶保溫效果*
e、試驗室蓋架採平面分度架，可任意調整角度，四面落霧及受霧方面**，試藥片放置數量多

福特標準中規定的相關要求如下：

                        Procedure
A.   Panels
     1.Scribe two diagonal lines from corner to corner across three test panels to the bare metal. Zinc-coated steel panels should be scratched through paint to zinc coating.（Do not penetrate to the bare steel）.
     2.Suspend the panels at an angle in the salt spray cabinet as specified in ASTM B 117 for the fime designated by the material specification （testing side up）.
     3.Rinse the panels with water, blot dry,and examine within 15 minutes.
       Measure and report in mm the maximum corrosion and blister creepage on either side of the scribed lines. Also examine panels for occurrence of surface blisters giving size and density according to ASTM D 714. In case of zinc-coated panels, measure the maximum distance of blisters and raised paint from the scribed line.
     4.Apply tape over each scribed line, in a parallel direction, using firm finger pressure to ensure contact with the panel surface（i.e.,scribe line to be visible）. This step is to be performed within 30 minutes after completion of Step 3.
     5.Within 90 +/- 30 s of application, remove the tape by pulling back rapidly （do not jerk） at as close to an angle of 180°to the panel as possible.

                       Evaluation
Report in mm, corrosion and/or blister creep and loss of adhesion after the tape test from scribed lines and occurrence of blistering and adhesion loss beyond the scribed lines.
B.    Parts
1.Wash parts in water to remove dirt and contamination.
2.Suspend the parts in the salt spray cabinet in car position for the time designated by the individual specification. Parts shall not be scribed unless otherwise requested by the applicable Engineering Specifications, and the position should be varied slightly if recesses tend to collect solution.
3.Rinse the parts with warm water and a soft sponge to remove runoff stain,blot dry and examine within 15 minutes.
4.Apply tape across the surface using firm finger pressure. this step, which is to be performed within 30 minutes after the completion of Step 3, is to help identify blistering.
5.Within 90 +/- 30 s of application, remove the tape by pulling back rapidly （do not jerk） at as close to an angle of 180°to the panel as possible.
 
                        Evaluation
Report occurrence of blistering and corrosion.

Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities.

本司專業生產銷售符合各類標準的鹽霧試驗箱，性能優良、技術*、服務周到，歡迎前來選購！